Your boat is an important investment, and you want to make sure it stays in top condition at all times. Even if you’re not an avid boater, having a boat available when you need it can be a valuable asset, especially if you live in an area that experiences extreme weather like hurricanes and tornadoes. Since it doesn’t matter if your boat parts from PartsVu look shiny and new if it’s not going to move when you push the throttle, regular maintenance is critical to keeping your boat safe and functional.
Clean All Surfaces
1. Clean the surface with a soft, lint-free cloth moistened with water or a mild detergent solution.
2. Wipe the surface dry with a clean, lint-free cloth to prevent streaks or residue from being left behind on the surface. Damp Proofing Contractor & Dry Rot Treatment London
3. Apply an automotive wax or synthetic sealant to protect and renew the original finish in one even coat (if applicable).
4. Use these same steps for any other surfaces that need cleaning, such as vinyl seats, rubber seals, plastic trims, etc.
5. For stubborn stains like grease or grime on vinyl seats, try using a citrus degreaser spray before applying your automotive wax to remove dirt and oil buildup.(provides protection)
6. Avoid scratching delicate surfaces while washing, use a nonabrasive cloth made specifically for this type of work; it will not damage those surfaces like a dishcloth can.
7. Remember that there is nothing wrong with simply washing down your boat once in awhile instead of going through all this rigamarole every time!
Tighten All Screws
It may seem like a small task, but not checking all the screws on a boat could lead to bigger problems. It is important to tighten all screws because they are what keeps your boat together. If they are loose, they can fall out, which will cause other parts to loosen as well. This will cause cracks in the hull or worse, holes in the hull. You should check your fasteners at least once per month to ensure that you don’t have any loosened or missing fasteners.
Inspect the Shaft
The shaft is one of the most important parts on a boat, which is why it needs to be inspected regularly. There are 2 things to check when inspecting your boat shaft; the tire, the u-joint, the coupler, and the grease.
Check for cracks in the tires. This can usually be done by looking for bubbles in them or feeling them with your fingers. If you find any cracks then replace all four tires immediately.
Check for excessive play in a u-joint. A loose joint will cause excessive vibration and noise so if you feel any looseness then tighten it up! A loose joint will cause excessive vibration and noise so if you feel any looseness then tighten it up! And don’t forget about checking the other two joints as well. Make sure that all joints have enough grease, but not too much. The last thing to inspect is how tight your coupling bolts are holding everything together. With these six easy steps you can rest assured that your boat is safe and sound!
Lubricate with Oil
Lubricating your boat parts from partsVu with oil is important because it helps the engine run smoothly and prevents corrosion. It also keeps your propeller from getting stuck. To lubricate your boat correctly, start by checking your engine manual to find out how often you need to change the oil. Then, locate the opening for the oil dipstick (this will vary depending on which type of engine you have). Remove the dipstick and wipe it clean before replacing it. Next, check that there is at least a quarter inch of oil on the stick before reinserting it into its holder. If there isn’t enough oil, add more until you reach that level. Finally, replace all caps on your boat’s parts before starting up your engine for a test drive.
Rinse All Areas
If your boat has been sitting for a while, you should rinse all areas with fresh water before using it. This will help remove any moisture that may have collected on the surfaces. This will also prevent the growth of mold and mildew in these places.
Before you rinse any area, make sure there is an adequate amount of fresh water available to wash away anything that might get flushed off during cleaning. After you’ve rinsed the area, make sure to dry it off with a clean towel to avoid potential corrosion from excess moisture in the air.
Clean the Tank
One of the most important things to do before you head out on the water is to clean your tank. You can do this by putting a few tablespoons of bleach in the tank. It is best to let it sit for a while before you drain it so that all bacteria are killed. You should also take care not to overfill your tank because this will cause water to overflow when you open it. In addition, make sure not to mix different types of fuel together because this will lead to an explosion hazard.
Change the O-Ring Seal
Replacing the O-Ring Seal can be a simple process. First, remove the old seal with a flathead screwdriver by wedging it underneath the old seal and prying up. Ensure that you have the replacement seal handy before removing the old one to avoid forgetting it at home. If you’re unsure if you need to replace this part, inspect the area around it for signs of leakage or corrosion (rust) which may indicate that it needs replacing. Once removed, clean out any debris or dirt that might be in there with some water and a rag before applying your new O-Ring Seal. Apply silicone grease to both sides of the new seal before placing it in its designated spot to help facilitate installation.